{"product_id":"radiomaster-mt12-gyro-module","title":"RadioMaster MT12 Gyro Control Module 2-Axis Hand-Gesture Control for MT12 Expansion Slot (EdgeTX Mixing)","description":"\u003ch2\u003eOverview\u003c\/h2\u003e\u003cp\u003eThe RadioMaster MT12 Gyro Control Module is a two-axis gyro that enables control of two channels using hand gestures. It integrates into the MT12 expansion slot and feeds hand movements into the control stream through the advanced mixing and programmability of EdgeTX, suitable for uses such as pan\/tilt gimbal control, RC model turret control, rear wheel steering, and more.\u003c\/p\u003e\u003cp\u003eFor product selection or setup help, contact support@rcdrone.top or visit https:\/\/rcdrone.top\/.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eTwo-axis gyro gesture input for controlling two channels\u003c\/li\u003e\n\u003cli\u003eDesigned for installation in the MT12 expansion slot\u003c\/li\u003e\n\u003cli\u003eWorks with EdgeTX mixing and model programmability\u003c\/li\u003e\n\u003cli\u003eOn-module sensor neutral calibration via button (status LED indication)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Supply\u003c\/td\u003e\n\u003ctd\u003eDC 3.3V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e8.3 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e65.0 x 33.0 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eX-axis Angle Range\u003c\/td\u003e\n\u003ctd\u003e90° (-45° to 45°)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eY-axis Angle Range\u003c\/td\u003e\n\u003ctd\u003e90° (-45° to 45°)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003col\u003e\n\u003cli\u003eRemove the battery from the bottom of the MT12.\u003c\/li\u003e\n\u003cli\u003eRemove the top cover from the MT12 by pushing away from the grip.\u003c\/li\u003e\n\u003cli\u003eInstall the gyro module at the top of the radio base.\u003c\/li\u003e\n\u003cli\u003ePlug the cable into the 5-pin connector in the battery compartment.\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch2\u003eHow to Use\u003c\/h2\u003e\u003ch3\u003eMT12 Radio Settings\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardware menu:\u003c\/strong\u003e Press \u003cstrong\u003eSYS\u003c\/strong\u003e and use \u003cstrong\u003ePAGE\u003c\/strong\u003e to navigate to \u003cstrong\u003eHARDWARE\u003c\/strong\u003e. Set \u003cstrong\u003eS3\u003c\/strong\u003e and \u003cstrong\u003eS4\u003c\/strong\u003e under \u003cstrong\u003ePots\u003c\/strong\u003e to \u003cstrong\u003eAxis X\u003c\/strong\u003e and \u003cstrong\u003eAxis Y\u003c\/strong\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCalibration in MT12:\u003c\/strong\u003e Press \u003cstrong\u003eSYS\u003c\/strong\u003e and use \u003cstrong\u003ePAGE\u003c\/strong\u003e to navigate to \u003cstrong\u003eHARDWARE\u003c\/strong\u003e, then enter \u003cstrong\u003e[Calibration]\u003c\/strong\u003e. At \u003cstrong\u003eSET AXIS MIDPOINT\u003c\/strong\u003e, place the MT12 level on a table and press the scroll wheel to calibrate the neutral point. At \u003cstrong\u003eMOVE AXIS\/POTS\u003c\/strong\u003e, pick up the MT12 and move it back\/forward and side-to-side with angles greater than 45 degrees.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput menu:\u003c\/strong\u003e Press \u003cstrong\u003eMDL\u003c\/strong\u003e and use \u003cstrong\u003ePAGE\u003c\/strong\u003e to navigate to \u003cstrong\u003eINPUT\u003c\/strong\u003e. Bind the gyro output to two input channels (example: Axis X (S3) to \u003cstrong\u003eI09\u003c\/strong\u003e and Axis Y (S4) to \u003cstrong\u003eI10\u003c\/strong\u003e). To set the source for an input, open the input’s \u003cstrong\u003eEdit\u003c\/strong\u003e menu, select \u003cstrong\u003eSource\u003c\/strong\u003e, press the scroll wheel, then tilt the MT12 so the source is detected.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMixer menu:\u003c\/strong\u003e Press \u003cstrong\u003eMDL\u003c\/strong\u003e and use \u003cstrong\u003ePAGE\u003c\/strong\u003e to navigate to \u003cstrong\u003eMIXER\u003c\/strong\u003e. Bind the gyro inputs to receiver output channels (example: Axis X to channel 3 and Axis Y to channel 4). For a channel, open its \u003cstrong\u003eEdit\u003c\/strong\u003e menu, select \u003cstrong\u003eSource\u003c\/strong\u003e, press the scroll wheel, then tilt the MT12 so the input is detected.\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eGyro Sensor Calibration (On Module)\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePress and hold the red button for 2 seconds to calibrate the sensor neutral point.\u003c\/li\u003e\n\u003cli\u003eDuring calibration, the red light flashes.\u003c\/li\u003e\n\u003cli\u003eA steady green light indicates normal operation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat’s Included\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e1 x MT12 Gyro Control Module\u003c\/li\u003e\n\u003cli\u003e1 x 5-pin JST cable (installed on module)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2 id=\"details\"\u003eDetails\u003c\/h2\u003e\u003cdiv class=\"details-gallery\"\u003e\n\u003cimg alt=\"RadioMaster MT12 gyro control module for 2-axis hand-gesture input on EdgeTX mixing (MT12 expansion slot)\" loading=\"lazy\" src=\"https:\/\/rcdrone.top\/cdn\/shop\/files\/RadioMaster-MT12-Gyro-Control-Module.jpg?v=1780740696\"\u003e\u003cp\u003eUse hand gestures to control two channels—ideal for pan\/tilt gimbals, RC turrets, or rear-wheel steering.\u003c\/p\u003e\n\u003cimg alt=\"Installation steps for MT12 gyro module: remove battery, remove top cover, install module, connect 5-pin JST cable\" loading=\"lazy\" src=\"https:\/\/rcdrone.top\/cdn\/shop\/files\/RadioMaster-MT12-Gyro-Control-Module_41b3e1a2-5f2c-4df5-a363-52cf177cf52a.jpg?v=1780740702\"\u003e\u003cp\u003eInstallation takes four quick steps: remove the battery and top cover, seat the module in the expansion slot, then plug in the 5‑pin connector.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"RadioMaster","offers":[{"title":"Default Title","offer_id":52970273669344,"sku":"HP0157.MT12-0047-1","price":18.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0643\/3210\/3904\/files\/MT12-GYRO_Gyro_ControlModule.jpg?v=1780591523","url":"https:\/\/rcdrone.top\/es\/products\/radiomaster-mt12-gyro-module","provider":"RCDrone","version":"1.0","type":"link"}