CHIHAI CHS-SM1530 Linear Stepper Actuator, 30mm Travel with Driver Options

CHIHAI MOTOR

$24.54 USD

Sale Sold out

Taxes included. Shipping calculated at checkout.

Configuration SM1530 Motor - 30mm Travel SM1519 Motor - 19mm Travel SM1530 + Standard Driver SM1530 + PLC Driver

Quantity

View full details

Overview

The CHIHAI MOTOR CHS-SM1530 is a compact linear actuator that converts two-phase stepper rotation into guided lead-screw travel. Its M3 x0.5 right-hand screw and plastic carriage provide30 mm effective travel. Choose the 1530 motor alone, a 1530 motor with standard or PLC-control driver, or the separate 1519 motor-only version with 19 mm travel.

Features

Single-axis guided screw drive with a stainless support shafts.
Reversible two-phase, four-wire bipolar stepper motor.
Right-hand M3 x0.5 lead screw on the SM1530.
Motor-only and driver-board packages corresponding to actual configurations.

Specifications

Item	Specification
Main model	CHS-SM1530-M3 xP0.5 permanent-magnet linear stepper
Structure	Single-axis lead-screw actuator with guided plastic carriage and stainless support shafts
SM1530 travel	30 mm effective linear travel
SM1519 travel	19 mm; separate motor-only configuration
SM1530 outer reference	15 x14.5 x60 mm; drawing60 mm maximum overall
Lead screw	M3 x0.5, right-hand thread, SM1530
Rated motor supply	6V DC with L6219 driver reference, SM1530
Phase current	400 mA per phase at 1000 pulses/s, SM1530
Phase resistance	15 ohm ±10% per phase at 20 °C, SM1530
Motor phases	2 phases,4 wires
Step angle	18 degrees per step, SM1530
Excitation	2-2 phase excitation; bipolar drive
Pull-out load reference	More than 200 g at 500 pulses/s, SM1530; not a torque or continuous payload rating
Maximum response frequency	More than 1200 pulses/s, SM1530
Maximum starting frequency	More than 900 pulses/s, SM1530; acceleration and actual load still matter
Insulation class	Class E for coils
Dielectric test reference	100V AC for one second
Insulation resistance	50 MΩ at 500V DC
Operating temperature	0 to+55 °C
Motor net mass	Approximately31 g, SM1530
Connection	XH2.54 four-pin; UL1571 AWG28;250 ±10 mm lead drawing reference

The detailed electrical and dimensional references below apply to SM1530. The separate SM1519 configuration has19 mm travel; do not apply the 1530 envelope, phase current or force reference to it.

Mechanical Dimensions and Tolerances

Area	SM1530 drawing references
Overall / body	60 mm max;45.0 mm main frame;12.0 mm motor section; motor diameter15.0 mm and19.5 mm end outline reference
Guide and mounting	48.0 ±0.05 mm and45.0 ±0.05 mm references;35.0 ±0.05 mm mount span;11.0 ±0.05 mm reference;19.0 mm reference
Cross-section	14.5 mm width;15.0 mm height reference;4.0 mm feature;10.95 mm reference;11.0 ±0.05 mm frame height
Small features	3.0 mm guide diameter;2.5 mm and0.5 mm references;2.0 and1.5 mm base features;2 xM2.5 tapped mounting holes
Remaining drawing annotations	4-2.0 and4-8.0 annotations retained in the drawing; check actual part and mounting detail before machining

All drawing dimensions are millimetres. The general tolerance table lists grades A, B and C without assigning a selected grade to every feature. Keep individually marked tolerances and verify the applicable grade before machining. The drawing angular-tolerance reference is ±0.1°.

Length range L(mm)	Grade A ±mm	Grade B ±mm	Grade C ±mm
L≤3	.02	.03	.05
3<L≤6	.05	.05	.08
6<L≤16	.07	.08	.10
16<L≤30	.10	.10	.12
30<L≤120	.10	.15	.18
120<L≤300	.15	.20	.25
300<L≤500	.20	.30	.40

Wiring and Driver Selection

Four-pin wire order: pin1 blue=B+, pin2 black=B−, pin3 red=A+, pin4 yellow=A−. Coil pairs are blue/black and red/yellow. The connector is XH2.54-4PIN. Use a suitable bipolar stepper driver and match current and voltage to the selected motor; do not connect the coils directly to a DC supply.

The standard-driver package includes the four-button display board. The PLC-driver package adds the pictured PUL/DIR/EN external-control connector. These choices include one driver board with one SM1530 motor; a PLC or power supply is not included. Confirm actual motor phase current and driver setup before running.

Configuration Guide

Selection	Motor	Travel	Included driver
SM1530 Motor - 30mm Travel	SM1530	30 mm	None
SM1519 Motor - 19mm Travel	SM1519	19 mm	None
SM1530 + Standard Driver	SM1530	30 mm	Standard push-button
SM1530 + PLC Driver	SM1530	30 mm	PLC-control push-button

Applications

Use the actuator for compact single-axis slides, small positioning or feed mechanisms, miniature printing/engraving development and instrument adjustment within the selected motor ratings. Combining axes requires additional mechanics and controls. This is not a complete two-axis XY cross-slide, medical device or certified treatment instrument.

What's Included

One selected linear stepper actuator with attached four-wire lead and carriage. A driver board is included only in the two SM1530 driver packages. No cross-axis platform, external controller, PLC, power supply or complete machine is included.

Installation and Operation

Check mounting dimensions, polarity and coil pairs before power-up. Provide adequate clearance throughout the selected travel. Commission with light load and increase gradually; avoid mechanical end-stop impact, excessive shaft loads and forcing the screw or carriage. Voltage, speed, load and duty cycle affect heat. Reference starting/response frequencies do not guarantee reliable motion at every load.

FAQ

Is this a complete XY slide?

No. Each selection contains one single-axis linear actuator; it does not include a second perpendicular stage.

What is different about the 1519 option?

It is a separate motor-only version with 19 mm travel, compared with 30 mm travel for SM1530. The 1530 parameter table is not a specification for1519.