BrotherHobby SE 2810 1180KV Motor (CW) - 6S, 12N14P, M5 Thread, 19x19mm Mount, N52H
BrotherHobby SE 2810 1180KV Motor (CW) - 6S, 12N14P, M5 Thread, 19x19mm Mount, N52H
BrotherHobby
Couldn't load pickup availability
Overview
The BrotherHobby SE 2810 1180KV Motor (CW) is a 6S-capable motor designed for builds using larger propellers, with an M5 prop adapter shaft thread and a 19 x 19 mm M3 mounting pattern.
Key Features
- SUS420 heat-treated steel shaft (SUS420)
- 7075 aluminum caps / bell cap (Al 7075), hard-anodized
- N52H arc magnet rotor (N52H)
- High-precision bearings (Japanese NMB 12 x 6 x 4)
- TU1 grade enameled wire; wire spec: 18# with 25 cm length
- Ultra-thin silicon steel stator sheet: 0.2 mm Kawasaki silicon steel
- Configuration: 12N14P
For pre-sales and technical support, contact support@rcdrone.top or visit https://rcdrone.top/.
Specifications
| Model | SE 2810 |
| KV | 1180KV |
| Configuration | 12N14P |
| Base casing material | Al 7075 |
| Bell cap material | Al 7075 |
| Stator material | 0.2mm Kawasaki silicon steel |
| Stator height (mm) | 10 (Kawasaki 1200# 0.2MM) |
| Stator dimension (mm) | 28.00 |
| Motor dimension (mm) | Φ33.3 x 39 |
| Prop adapter shaft thread | M5 |
| Shaft | SUS420 |
| Bolt pattern | M3 (19 x 19mm) |
| Bearings | Japanese NMB 12 x 6 x 4 |
| Rotor | N52H arc magnets |
| No. of Cells (LiPo) | 6S |
| Wire AWG | 18# 25cm length (also shown as 18#, 250mm) |
| Weight | 67.2g |
| Weight including cable (g) | 68.10 |
| Internal Resistance (mΩ) | 63.60 |
| Idle Current @ 10V (A) | 1.03A/10V |
| Max power (W) | 940.80 |
| Max Current (A) | 39.20 |
| Insulation Resistance | >= 0.5MΩ |
| Dynamic balance requirement standards | <= 3mg |
| Coil Test | PASS |
Prop Test Report (1180KV)
Test setup (as shown)
- Propeller: HQ 7X4X3
- ESC: 6S 45A
Load Test Data (HQ 7X4X3)
| Throttle (%) | Voltage (V) | Current (A) | RPM | Thrust (gf) | Input Power (W) | Thrust efficiency (G/W) |
|---|---|---|---|---|---|---|
| 30 | 24.00 | 2.00 | 7812 | 326.00 | 48.00 | 6.79 |
| 40 | 24.00 | 3.10 | 9440 | 472.00 | 74.40 | 6.34 |
| 50 | 24.00 | 5.00 | 11067 | 660.00 | 120.00 | 5.50 |
| 60 | 24.00 | 9.00 | 13387 | 1004.00 | 216.00 | 4.65 |
| 70 | 24.00 | 15.00 | 15420 | 1386.00 | 360.00 | 3.85 |
| 80 | 24.00 | 23.80 | 17756 | 1862.00 | 571.20 | 3.26 |
| 90 | 24.00 | 32.00 | 19410 | 2257.00 | 768.00 | 2.94 |
| 100 | 24.00 | 39.20 | 19880 | 2436.00 | 940.80 | 2.59 |
- Inside motor copper wire temperature: 76°C (ambient temperature: 26°C)
- Temperature note: inside copper wire temperature measured running 2 minutes at 100% throttle; bench data for reference only.
What’s Included
- SE 2810 motor x1
- M3*8 screw x4
- M5 flange nut x1
Applications
- 6S multirotor builds using 7-inch class propellers
Notes
- Some images also show specifications and prop test data for a different SE 2810 variant (1350KV). Those values are not for the 1180KV (CW) version listed on this page.
Details
The BrotherHobby SE 2810 motor is clearly labeled 2810-1180KV on the housing for easy identification during builds and replacements.
BrotherHobby SE 2810 motor specs list a 1350KV rating, 67.2g weight, and up to 2.5kg maximum pull force per motor.
The BrotherHobby SE 2810 1180KV motor features a compact black can and threaded shaft for straightforward prop installation on larger drone setups.
The BrotherHobby SE 2810 1180KV motor uses an M5 shaft and a 4×M3 mounting pattern, with a 39mm body length and Ø33.3mm diameter shown in the drawing.
The BrotherHobby SE 2810 1180KV motor comes with four M3×8 screws and an M5 flange nut for mounting.
The BrotherHobby SE 2810-1350KV motor report lists key specs like 12N14P configuration, 6S support, and HQ 7x3.5x3 prop test results.
The SE 2810 1180KV motor report includes a dimension drawing and a 24V HQ 7x4x3 prop test table with thrust, current, and efficiency readings.
Related Collections
