BrotherHobby Avenger 2810 V5 910KV CW Brushless Motor (6S) M5 Thread, 12N14P, 69g, Φ33.3x40
BrotherHobby Avenger 2810 V5 910KV CW Brushless Motor (6S) M5 Thread, 12N14P, 69g, Φ33.3x40
BrotherHobby
Couldn't load pickup availability
Overview
BrotherHobby Avenger 2810 V5 910KV Motor (CW) is a brushless motor designed for 6S setups, with an M5 prop adapter shaft thread and 12N14P configuration. The Avenger 2810 V5 series is commonly paired with folding propeller systems for portable multirotor builds.
Key Features
- SUS420 heat treated steel shaft
- Aviation grade 7075 aluminum caps (hard anodized), hollow-carved design for weight saving and heat dissipation
- N52H arc magnet with consistent air gap for a stable magnetic circuit
- TU1 grade enameled wire (high full slot ratio, low internal resistance)
- Ultra-thin non-oriented silicon steel sheet (high permeability and low eddy loss)
- Premium high precision bearings (axial-load capable)
Specifications
| Model | Avenger 2810 V5 |
| KV | 910KV |
| Configuration | 12N14P |
| No. of Cells (LiPo) | 6S |
| Base casing | Al 7075 |
| Bell cap | Al 7075 |
| Shaft | SUS420 |
| Prop adapter shaft thread | M5 |
| Bolt pattern | M3 (19x19mm) |
| Bearings | 12x6x4 |
| Rotor / Magnet | N52H arc magnets |
| Stator | 10mm |
| Stator dimension (mm) | 28.00 |
| Motor dimension (mm) | Φ33.3x40 |
| Wire AWG | 18# 25cm length |
| AWG | 18#, 250mm |
| Weight | 69g with 25cm SR wires |
| Weight including cable (g) | 69.00 |
| Internal resistance (mΩ) | 89.00 |
| Idle current @14V (A) | 0.82A/10V |
| Insulation resistance | >= 5MΩ |
| Coil test | PASS |
| Dynamic balance requirement standards | <= 6mg |
| Propeller connector | Propeller Connector-23x4.1 |
Performance Data (Test Report: Folding 9453F Triblade)
| Throttle | 100% |
| ESC | 6S 50A |
| Voltage | 25.2V |
| Max power | 1169.28W |
| Max current | 46.40A |
| Thrust | 3367g |
| Thrust efficiency | 2.88 |
Load Test Data (Avenger 2810 V5 + Folding 9453F Triblade)
| Throttle (%) | Voltage (V) | Current (A) | RPM | Thrust (gf) | Input Power (W) | Thrust efficiency (G/W) |
|---|---|---|---|---|---|---|
| 30 | 25.20 | 3.60 | 6167 | 652.00 | 90.72 | 7.19 |
| 40 | 25.20 | 7.20 | 7806 | 1037.00 | 181.44 | 5.72 |
| 50 | 25.20 | 12.40 | 9323 | 1440.00 | 312.48 | 4.61 |
| 60 | 25.20 | 17.90 | 10421 | 1858.00 | 451.08 | 4.12 |
| 70 | 25.20 | 25.30 | 11406 | 2250.00 | 637.56 | 3.53 |
| 80 | 25.20 | 33.50 | 12662 | 2735.00 | 844.20 | 3.24 |
| 90 | 25.20 | 37.70 | 13175 | 2926.12 | 950.04 | 3.08 |
| 100 | 25.20 | 46.40 | 13933 | 3367.00 | 1169.28 | 2.88 |
Copper wire temperature note: The inside of motor copper wire: 106°C (ambient temperature is 26°C). Remark: The temperature is motor inside copper wire temperature running 2MIN at 100% throttle.
Folding Propeller Rotation Diameter (Hole Pitch: 23mm)
Manual measurement with slight deviation from actual data.
| Propeller | Rotating diameter |
|---|---|
| Folding 1248 Triblade | 311.1mm |
| Folding 1558 Triblade | 379.7mm |
| Folding 1865 Triblade | 453.9mm |
| Folding 9453 Triblade | 244.8mm |
| Folding 1148 Triblade | 285.3mm |
| Folding 1660 Triblade | 395.1mm |
Support
For compatibility questions (motor rotation direction, mounting pattern, prop adapter thread, or 6S ESC pairing), contact support@rcdrone.top or visit https://rcdrone.top/.
Details
BrotherHobby Avenger 2810 V5 brushless motors with folding propellers suit compact drone setups where easy carry and storage matter.
The BrotherHobby Avenger 2810 V5 910KV motor is rated for a 6S setup, with a listed test thrust of 3367g at 100% throttle using a 9453F triblade prop.
The BrotherHobby Avenger V5 910KV brushless motor features a compact can design with clear 910KV marking for quick identification during builds.
The Avenger 2810 V5 motor uses a SUS420 steel shaft, N52H arc magnets, enamelled copper windings, and high‑precision bearings for a robust rotor and stator assembly.
The Avenger 2810 V5 motor uses an M5 threaded shaft and M3 mounting pattern, with a 33.3 mm body diameter and 40 mm overall height for fit checks.
Folding tri-blade prop options list a 23mm hole pitch with rotating diameters from 244.8 mm up to 453.9 mm for fit planning.
The BrotherHobby Avenger 2810 V5 910KV motor pairs with a 9453 three-blade folding propeller for compact storage and flight readiness.
A step-by-step folding triblade paddle installation sequence helps ensure the prop hub, paddles, and nut are assembled in the correct order.
BrotherHobby Avenger V5 brushless motors feature a compact black can design with top-mounted prop adapters for multirotor builds.
The Avenger V5 motor uses a propeller connector and spacer stack with a folding propeller and flange nut for secure assembly.
A brushless motor bundle with CCW folding triblade prop blades and basic mounting hardware helps simplify replacement and setup.
The Avenger V5 motor comes with CW folding triblade propellers and a basic hardware kit for straightforward installation.
The set includes the motor plus a three-blade folding propeller kit with connector, screws, spacers, flange nut, pins, and a spring.
The package includes the motor along with folding propeller blades, propeller connector parts, screws, spacers, and a flange nut, with CW/CCW prop direction options.
BrotherHobby Avenger 2810 V5 910KV motor documentation lists 12N14P configuration, 33.3×40 mm dimensions, and 6S test data with a 9453F triblade prop.
Related Collections
