• SpeedyBee F405 V3 30x30 Flight Controller
  • SpeedyBee F405 V3 30x30 Flight Controller
1 2

SpeedyBee F405 V3 30x30 Flight Controller

SpeedyBee F405 V3 30x30 Flight Controller

SpeedyBee

$42.00 USD
$42.00 USD
Sale Sold out
Taxes included. Shipping calculated at checkout.

51 orders in last 90 days
  • PayPal
  • Visa
  • Mastercard
  • American Express

Warehouse: China/USA/Europe, can delivery to all countries;

Free Shipping: 9-15 days;

Express Shipping: 5-8 days;

Return&Refund: 30 Days.

View full details

 

Specifications

Product Name SpeedyBee F405 V3 30x30 Flight Controller
MCU STM32F405
IMU(Gyro) BMI270
USB Port Type Type-C
Barometer Built-in
OSD Chip AT7456E chip
BLE Bluetooth Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available .
WIFI Not supported
DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Blackbox MicroSD Card Slot *Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.
BetaFlight Camera Control Pad Yes(CC pad on the front side)
Current Sensor Input Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
Power Input 3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin cable or G, V pads from the bottom side of the flight controller.
5V Output 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
9V Output 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal M1 - M4 on bottom side and M5-M8 on front side.
UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry UART R5(UART5)
I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer BZ+ and BZ- pad used for 5V Buzzer
BOOT Button Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input Supported. Named as RS on the front side.
Smart Port / F.Port Not supported
Supported Flight Controller Firmware BetaFlight(Default),INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)
Firmware Target Name SPEEDYBEEF405V3
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 41.6(L) x 39.4(W) x 7.8(H)mm
Weight 9.6g

Details

SpeedyBee F405 V3 BLS 50A Stack
So so many cool features,
at an unbelievable price!
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
$69.99 for a Bluetooth 50A
Stack? That's ridiculous
I know right? With only $69.99, you will get an STM32F405 FC
(better than F411), onboard 4-level battery life indicator, 4GB
Blackbox SD card slot for your flight logs, 4 groups of LED strip pads,
complete with a DJI plug* for your digital quad, and built-in Bluetooth
for wireless configuration on the SpeedyBee app.
Don't forget about the powerful 50A 4-in-1 ESC, built with TVS
protective diode + Japan made TDK SMT capacitors + external
1000uF low ESR capacitor, everything is for durable build and
smooth flight.
All of that for only $69.99! Top-shelf spec at a crazy low price, what
are you waiting for?
* The DJI Air Unit plug is completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
Configure your FC and ESC
via Bluetooth
With SpeedyBee app, turn your phone into an all-in-one
FC configurator and tune your quad anytime, anywhere.
Experience wireless, fully configurable ESC experience with
SpeedyBee app.
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
Powerful Real 50A 4-in-1 ESC!
Built with the robust BB21 MCU and large motor pads for easy
soldering. Built with Japan made TDK filtering SMT capacitors +
onboard TVS protective diode, brings smooth flight experience.
Real 50A output, ready for your baddest 6S motors.
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
Forgot your LiPo checker?
Just look at the FC!
Built with a 4-level LED battery indicator, now you can fly
anywhere worry-free - even without your lipo checker!
 

* 1 light constantly on: battery level 10-25%

1 light blinking: battery level < 10%

SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
8 motors output for X8/Y6/
fixed-wings
You could use this stack to build your X8 drones, Y6 drones or
fixed wings. Forget about crawling through your massive build
just to plug in that USB cable. Just take out your phone to
configure everything in the SpeedyBee app.
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
Change motor directions
wirelessly!
Finishing your latest build? Just replaced your motor after a crash?
Take your smartphone out, and configure your motor direction
wirelessly with the latest SpeedyBee app. Works for all
BLHeli32 / BLHeli_S / BlueJay ESCs.
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
4 sets of LED pads with
simple switching
Need more visibility at night? Just solder up your LED strips*
and blaze the darkest trail you can find. With just one tap on t
he BOOT button, you can cycle through all different LED presets**
and pick the one you love!
* LED strips could be purchased here
**Or long press the boot button to switch to Betaflight LED mode
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
1000uF Low ESR capacitor +
TVS protective diode =
Extra protection
The ESC is built with TVS protective diode to absorb the voltage
spike when you plug in the battery, or during crashes that block
your props.We also provide a humongous 1000uF low ESR
capacitor, ensuring clean data from the gyro to the FC.
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
And packaged with more
useful features
● Built-in barometer for accurate height calculation
● SD Card slot can support up to 4GB Blackbox data*
● Dedicated DJI Air Unit connector for a quick digital build
● 9V 2A + 5V 2A individual BECs
● 4 x UARTs for your receiver + VTX + camera + GPS.
● Power your GPS with a USB cable - no battery needed.
   No extra heat, no worries.
● 22mm cutouts for FPV camera in your tight build
*Betaflight firmware requires the type of the microSD card to be
either Standard (SDSC) or High capacity (SDHC), so extended
capacity cards (SDXC) are not supported(Many high-speed U3 cards
are SDXC). Also the card MUST be formatted with the FAT16 or FAT32
(recommended) filesystems. So, you could use any SD card less than
32GB, but the Betaflight can only recognize 4GB maximum.
We suggest you use this 3rd party formatting tool and choose
'Overwrite format' then format your card. Also check out here for
the recommended SD cards or buy the tested cards from our store.
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
Dimensions
SpeedyBee F405 V3 30x30 Flight Controller, SpeedyBee F405 V3 STACK
Wiring Diagram
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK

The SpeedyBee F405 V3 30x30 Flight Controller features a connection with motors, power cable, motor 4, motor 2, speedyucciesssor, DR DD motor 3, motor 1. This product also includes a low ESR capacitor and XT60 power cable for efficient voltage regulation.

 
SpeedyBee F405 V3 STACK

The SpeedyBee F405 V3 30x30 Flight Controller features a cable connection option for DJI Air Unit vs RunCam Link/Caddx Vista. The kit includes a 6-pin cable that comes with the F405 V3 stack (see accessory No.10 in the package section). Additionally, it supports SBUS I2 and GND connections.

 
SpeedyBee F405 V3 STACK

Important notice for SBUS receiver: When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2). If you are also using a DJI Air Unit and have connected it to the flight controller through the dedicated 6-pin harness on the back, you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully. Important notice for ELRS receiver: We recommend connecting the ELRS receiver TX and RX to the T2 and R2 pads on the flight controller. However, when using a DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness.

 
SpeedyBee F405 V3 STACK

SpeedyBee F405 V3 30x30 Flight Controller features 4-in-1 ESC, FPV camera, and receiver with extra PWM output. It has MCU: F405 R3 T3 G M5 M6 M7 M8, Telis9 SBUS Bluetooth chip, orange LED indicator, 8 USB type-C ports, and 4-level LED battery indicator. It includes I/O port for peripherals, BOOT button, SpeedyBee green LED, SDA/SCL pins, 5V LED power indicator, BAT and GSV battery indicators. It also features OSD chip (AT7456E), gyro (BMI270), VTX (Analog/DJI) with 8-pin connector to ESC.

 
SpeedyBee F405 V3 STACK

SpeedyBee F405 V3 30x30 Flight Controller with BLS 50A 4-in-1 ESC Driver, compatible with 4 motors (MOTOR 2, MOTOR 3, MOTOR 4), and features an 8-pin connector for FC connection. Equipped with MCU BB28T, SpeedyBee TVS Diode, and 12V/84CN.

 
SpeedyBee F405 V3 STACK

SpeedyBee F405 V3 Flight Controller Product Image: SpeedyBee F405 V3 30x30 Flight Controller. Features include EEEFEEE (Efficient), High-Energy, and Fast Processing for precise flight control. Includes M3*8mm Silicone Grommets for FC connection, SH 1.Omm 2Smm-length 8pin Cable for FC-ESC connection, and DJI 6pin Cable (80mm) for a secure connection.




Manual

Summary of product information for SpeedyBee F405 V3 30x30 Flight Controller.English SpeedyBee F405 V3 30x30 Flight Controller, The information works for all BLHeli32, BLHeli_S, and BlueJay ESCs.中文

 

 

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Drone Categories