CHIHAI MOTOR CHR-RS380SM High-Speed DC Motor, 11.1V
CHIHAI MOTOR CHR-RS380SM High-Speed DC Motor, 11.1V
CHIHAI MOTOR
পিকআপের উপলভ্যতা লোড করা যায়নি
Overview
The CHIHAI MOTOR CHR-RS380SM-6022G-55 is a red-can brushed DC motor with a 22TPA winding reference,two ball bearings and ferrite magnets. Choose a round or D-shaped shaft,with optional soldered bullet-connector leads and a blue finned heatsink. The no-load speed references are 35000 rpm at 7.4V and 53000 rpm at 11.1V.
Features
- Front and rear ball-bearing support.
- Wet-pressed ferrite magnets and copper-wound rotor.
- Round-shaft and D-shaft versions have separate dimensional drawings.
- Optional15 cm AWG16 bullet-connector leads and clip-on heatsink.
Specifications
| Specification | Value / scope |
|---|---|
| Brand/model | CHIHAI MOTOR CHR-RS380SM-6022G-55 brushed high-speed DC motor |
| Winding reference | 22TPA graphic reference |
| No-load speed references | 35000 rpm at 7.4V DC;53000 rpm at 11.1V DC |
| Body reference | 27.7 mm diameter×37.8 mm can length |
| Magnets | Wet-pressed ferrite magnets |
| Bearings | Two ball bearings,front and rear |
| Rotor construction | Copper winding,dynamic balancing and heat-resistant bonding at commutator connections |
| Brush construction | Carbon brushes with damping compound reference;no complete-motor temperature limit specified |
| Motor weight | Approximately72 g,without optional lead/heatsink assemblies |
| Round-shaft drawing | 2.3 mm diameter(+0/−0.005);14±0.5 mm projection;37.8±0.2 mm can;55 mm overall drawing reference |
| Round-shaft interfaces | Two M2.6 mounting holes on16 mm pattern;10 mm front/rear registers;2.6 mm shoulder;2.3 mm rear terminal allowance;6.5×3 mm terminal reference |
| D-shaft drawing | 2.3(+0.006/0) mm diameter;1.8±0.02 mm flat;8±0.1 mm flat length;15±0.5 mm projection |
| D-shaft body and fit | 38±0.2 mm can;57±0.1 mm overall drawing reference;27.9 mm maximum body diameter;16 mm mounting pattern(+0.05/0) |
| Other D-shaft drawing references | 10±0.3 mm front register;10±0.3 mm rear register;2.8±0.5 mm rear allowance;3.5 mm shoulder;3.0 mm maximum screw-depth reference;3 mm terminal reference |
| Rotation reference | CCW in the marked drawing/test viewing orientation;follow RED+ terminal mark |
| Optional soldered leads | 15 cm AWG16 red/black leads with bullet connectors |
| Optional heatsink | Blue finned clip-on heatsink shown;dimensions and weight not specified |
7.4V Performance Test
The following reference points were measured at 7.4V in the marked CCW direction. No-load,stall,maximum-efficiency and maximum-output conditions are separate operating points. These7.4V results must not be treated as measured11.1V load performance.
| Operating condition | Reference values |
|---|---|
| Test supply / direction | 7.4V DC /CCW |
| No-load speed/current | 35000 rpm /1.700 A |
| Stall torque/current | 1371.54 gf·cm /70.00 A |
| Maximum-efficiency point | 30281 rpm;10.91 A;184.92 gf·cm;57.43 W output;71.17% efficiency |
| Maximum-output point | 17500 rpm;35.85 A;685.77 gf·cm;123.15 W output |
The123.15W figure is the maximum-output test point,not a continuous output rating. The70A stall-current reference is a limiting condition,not an acceptable running load. Avoid stalled or overloaded operation and use wiring,switching and a power source matched to the actual motor current.
Shaft Fit and Wiring
Check the selected shaft drawing before fitting a pinion or coupler. The round version shows a 14 mm projection;the D-shaft version shows15 mm and an 8 mm flat-length reference. Their can-length,overall-length and diameter references also differ slightly. Do not apply the D-flat dimensions to the round shaft.
Follow the RED+ terminal mark and the drawing's viewing orientation for the CCW reference. Red and black soldered leads are included only on named lead options. Each lead assembly uses 15 cm AWG16 wire and bullet connectors. Motor-only options retain bare terminals.
Cooling and Installation
High-speed operation produces heat quickly. For compatible model-car installations,use the optional heatsink and suitable airflow,and monitor temperature during operation. Extended operation without adequate cooling can damage the motor. A heatsink does not establish a continuous-power or temperature guarantee. Keep mounting hardware clear of the rotor and use the selected drawing's mounting and screw-depth references.
Applications
Compatible model-car and compact high-speed drive projects where the shaft,voltage,speed,current and cooling arrangements fit the mechanism. The selection does not include a gearbox or pinion.
What's Included
| Selected configuration | Contents |
|---|---|
| Round-Shaft Motor | 1 round-shaft motor |
| Round-Shaft Motor + Soldered Bullet Leads | 1 round-shaft motor with 15 cm AWG16 bullet-connector leads |
| D-Shaft Motor | 1 D-shaft motor |
| D-Shaft Motor + Soldered Bullet Leads | 1 D-shaft motor with 15 cm AWG16 bullet-connector leads |
| Round-Shaft Motor + Heatsink | 1 round-shaft motor and 1 heatsink |
| Round-Shaft Motor + Leads + Heatsink | 1 round-shaft motor with 15 cm AWG16 leads and 1 heatsink |
| D-Shaft Motor + Heatsink | 1 D-shaft motor and 1 heatsink |
| D-Shaft Motor + Leads + Heatsink | 1 D-shaft motor with 15 cm AWG16 leads and 1 heatsink |
A motor-only option does not include leads or a heatsink. A power supply,speed controller,pinion,coupler and application equipment are not included.
FAQ
Are the round and D-shaft versions dimensionally identical?
No. Their shaft projection and drawing references differ. Use the selected shaft's complete drawing.
Is123.15W a continuous output rating?
No. It is a maximum-output test point at 7.4V. Continuous suitability depends on load,cooling and current.
Do the 7.4V test values describe11.1V operation?
No. Only the 53000 rpm no-load reference is provided at 11.1V. The detailed load test is at 7.4V.
Which options include bullet-connector leads?
Only the options named with soldered leads. Their red/black lead assembly is 15 cm AWG16.
Does every option include a heatsink?
No. Select a heatsink option for the blue finned clip-on heatsink and provide appropriate cooling for the application.
Visual Details
