FLAGSHIP STACK
AFFORDABLE PRICE
wirelessly + full FC configuration
transfer. Update FC firmware with your smartphone in just 1 minute!
Connect this FC via Bluetooth and fully configure any setting for
Betaflight/INAV as you want.
1 minute anytime, anywhere
dive into your Blackbox data every time you land your quad. Just take
your smartphone out, connect, and download your flight in 20 seconds.
The path to progress has never been easier.
Just plug them all in!
digital video transmitter, receiver, camera, VTX, and GPS to complete
your build in no time. Also comes with 4x LED plugs so you can light
up your quad with no headache. Prefer soldering? Just flip the board
and start working on it.
direction wirelessly
motor after a crash? Take your smartphone out,
and configure your motor direction wirelessly
with the latest SpeedyBee app. Works for all
BLHeli32 / BLHeli_S / BlueJay ESCs.
your X8 cinelifters!
crawling through your massive build just to plug in that USB cable.
Just take out your phone to configure that X8 monster wirelessly
before that challenging commercial shot. Professional FPV pilots
got no time to waste.
with 4x LED plugs
darkest trail you can find, no soldering required. With just one tap
on the Boot button, you can cycle through all different LED presets*
and pick the one you love!
Just look at the FC!
worry-free - even without your lipo checker!
=500MB onboard Blackbox
flash memory
Blackbox flash memory. Or keep your encrypted Area 51 files in
it for your top-secret Man in Black mission. Whatever suits your
tactical purpose.
rate of 1000(instead of 1024), so the display capacity on your
computer will be slightly less than 500MB.
features
● Power your GPS with a USB cable - no battery needed
● 22mm cutouts for FPV camera in your tight build
● Built-in barometer for accurate height calculation
Blast through any obstacle during freestyle with no worry, or
keep that highest throttle position during races.
protective diode = Extra protection
when you plug in the battery, or during crashes that block your props.
We also provide a humongous 1000uF low ESR capacitor, ensuring
clean data from the gyro to the FC.
Tested by 2 top racing pilots with both over 1500 packs, or you can
put it to the test yourself.
Why not?
the best PWM frequency* to get for your build without any limitation.
frame, motors, props, and other factors. Higher PWM frequency
doesn't necessarily means smoother flight. If the default 48KHz is
not working for your build, you can increase the value gradually
until you find the sweet spot. Check your motor temperature to
avoid overheating.
no overheating in any condition
heat from your MOSFETs ensuring stable current flow at a high
throttle position. Great benefit in a stylish blue finish.
4-in-1 ESC for SpeedyBee F7 V3 with a 50A current rating and 32-bit processor, ideal for racing drones.
SpeedyBee F7 V3 BL32 50A 4-in-1 Electronic Speed Controller (ESC) with LED Display, Supports DSHOT and Oneshot125 protocols.
SpeedyBee F7 V3 BL32 50A 4-in-1 Electronic Speed Controller (ESC) for Multi-Rotor Aircraft. With its compact design and high-performance capabilities, this ESC is suitable for a wide range of applications.
The SpeedyBee F7 V3 BL32 50A 4-in-1 ESC requires specific setup for SBUS and ELRS receivers. For SBUS receivers, connect the SBUS signal wire to the front side of the flight controller (UART2). If using a DJI Air Unit (V1), disconnect the SBUS signal wire from the air unit harness. For ELRS receivers, connect TX and RX to T2 and R2 on the flight controller. However, if using a DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly. In this case, disconnect the SBUS signal wire from the air unit harness.
SpeedyBee F7 V3 BL32 50A 4-in-1 ESC, Cable Connection: Versus DJI 03 Air Unit Use 6-pin cable comes with the F7 V3 stack (See accessory No.3 in package section). Supports SBUS, GND and L/L channels. Operating Voltage: 7.4V-26.4V. Compatible with RunCam Link and Caddx Vista air units.
SpeedyBee F7 V3 BL32 50A 4-in-1 ESC: A multi-functional electronic speed controller with a powerful output of 50A, suitable for various applications. It features a high-performance 32-bit MCU and advanced algorithms for stable flight control.
SpeedyBee F7 V3 BL32 4-in-1 ESC, featuring a 50A rating. This 4-in-1 ESC combines motor driver and power management functions into one compact unit. It includes a CNC heat sink with capacitor pin and hole for GND, BAT+, and an 8-pin connector to the flight controller.
